Note: Once your keypad is programmed to your garage door opener, chaning your PIN to another code is easy. Now follow the instructions below to link your keypad to your Genie of Fairview Door opener. Enter the PIN of your choice (3 to 8 numbers) and press PROGRAM.Press and let go in order the 3, 5, 7 and PROGRAM keys.To clear out the factory settings or the previous code, press and hold both the PROGRAM key and the Up/Down arrow keys until the red light on the keypad flashes twice and goes out. (this keypad is off-white with a flip-up cover and the PROGRAM key is above the 2 key) Model 3: Programming instructions for your Genie of Fairview GK-BX Wireless Intellicode Keypad. While the indicator light is blinking enter your PIN number and Press the UP/DOWN arrow button several times ( 3 or 4 ) until the door is activated. Once you’ve set the keypad code go to your Genie of Fairview motor head follow the instructions below: Enter your chosen PIN, anywhere from 3 to 8 numbers and press PROGRAM (the red light should blink twice as fast and turns off, indicating it took your code).To program a new code press and let go in order the 3, 5, 7 and PROGRAM keys.The red light on the keypad will blink once and turn off. To erase the old PIN (Personal Idendification Code) press and hold down, in order, the PROGRAM, 6 and UP/Down Arrow keys.(off-white with flip-up cover – program key above the 3 key) While the indicator light is blinking enter your PIN number and Press the SEND button several times ( 3 or 4 ) until the door is activated.
This small black button is always found near the floppy antenna wire and is usually behind the light cover for your light bulbs. Gently press and release the radio receiver Learn Code button on the motor head in your garage to start the red indicator light next to the button will start blinking. Close cover fully and Proceed to Part 2.(red light blinks twice as fast – this tells you it took your PIN) Enter the Personal Identification number (PIN) of your choice.(the indicator light on the keypad will blink one and go out) Press and hold both the “PROG” and “8” keys and open the cover until it latches.To Reset your Genie of Fairview Intellicode Wireless Keypad follow these steps Model 1: Intellicode Models GWKIC, ACSDG ( black with slide-up cover and the work “Intellicode” printed on the cover. Genie Wireless Intellicode Keyless Entry Pad Programmingģ Models were made for Intellicode remotes, shown here from the oldest to the newest. Continue until you have 4 Door Code numbers for a 12 switch remote, or 3 Door Code numbers for a 9 switch remote. Look at the next 3 switches and determine its code number. Look at the chart below and write down the corresponding Door Code Number. Look at the first 3 switches and determine which ones are up and which are down. The Door Code in step 4 above is determined by the internal code switches inside one of your remotes. Enter your PIN and press the Star (*) key. Test keypad by sliding the cover up until it latches.Enter the Door Code determined by Chart A below and this time press the Star (*) key.Enter your PIN of your choice and press the # button.Open the cover back up and press in order the 3, 5, 7 and # keys.While holding down on the # and 8 keys at the same time slide the cover up the rest of the way until it clicks or latches. Reset keypad by sliding the cover half way up.If your keypad looks like this but has Intellicode on the cover go to the next set of programming instructions below. This keypad is NOT compatible with Genie of Fairview Intellicode remotes. The keypad is black with a slide-up cover showing the Genie logo only. This keypad works with remotes having either 9 or 12 internal code setting switches and 390 frequency. Genie of Fairview Wireless Keypad Model GPWK-12, GWK
0 kommentar(er)
